Firmware & Changelog (LoRaWAN GPS)

Firmware Downloads

Current Hardware Revision 3

Legacy Hardware Revision 2

Downloads:

Legacy Hardware Revision 1

Downloads:

Changelog

8.0.5 - 2020-08-10

Fix

• LoRaWAN: NewChannelReq can remove channels by setting the Frequency to 0 instead of just disable them
• LoRaWAN: Fix bug where NBTrans > 1 leads to multiple responses from LoRaWAN stack

8.0.4 - 2020-08-06

Fix

• Fix internal Selftesting result format.

8.0.3 - 2020-08-06

Fix

• Remove random payload in reboot request ACK upload

8.0.1 - 2020-08-05

Fix

• Fix config problem with low SF.

8.0.0 - 2020-08-05

Changed

• Change official product name to LOB-S-GPS-LW-3.
• Verify LoRaWAN Stack using official testing tool by LoRaWAN-Alliance.
• Remove OpMode (class C), ADR, and time sync over LoRaWAN
• Change internal logic of LostReboot-feature to use ACKs for checking for Network.

Added

• Low Voltage Protection

Fix

• Fix Voltage StepUp logic for GPS and LoRa
• Send uplink before reboot when ACK required.

v7.1.0 - 17.06.2020

Added

• Add timestamp for last movement event to Port 2 payload
• Add config parameter movementDistance that configures how GPS-position changes are calculated as movement events.

Fixed

• LoRaWAN 1.1 issue that sometimes led to invalid DevNonces used for OTAA Join.
• Make sure, mode changes from active to passive are reported in final uplink before change
• Fix an issue that could lead to all zero position data sent as valid position
• Upgrade to Lobaro LoRaWAN Stack 1.2.2 (RX Window adjustment).

v7.0.0 - 28.04.2020

• Completely rewrite firmware for new board rev3 with new LoRaWAN features and concepts.
• Extend Payload format on port 2 (add HDOP and Timestamp of last Fix).
• Listen to MEMS events while not asleep.
• Check for movement by GPS to update activity mode.
• New LED blinking patterns.
• Add regular status message on port 1.
• Update to new Lobaro LoRaWAN Stack (LoRaWAN v1.1, remote Configuration via Downlink, Class C, ...).
• Enable Time synchronisation from GPS.
• Change naming from "Alive Mode" to "Passive Mode" for easier distinguishing from "Active Mode".
• Reduce power consumption during deep sleep by ~20%.
• Removed Cayenne Payload Format

v6.1.0 - 09.12.2019

• added new parameters to increase accuracy: maxHDOP & maxDataAfterFix

v6.0.3 - 02.08.2019

• fixed temperature sensor readout

v6.0.2 - 22.07.2019

• inverted powerpin for telit module (hardware v2.1)
• added nmea prefix GN ( Glonass+GPS ) to the parser

v5.0.5 - 09.01.2019

• Update LoRaWAN Stack
• Enable stepUp if needed by battery condition

v5.0.4 - 15.11.2018

• update board driver

v5.0.3 - 15.11.2018

• fix signed issue with longitude

v5.0.0 - 26.10.2018

• Add option for Cayenne LLP Payload format
• Adjust payload format to support neagtive values
• Add Altitude

• Send GPS coordinates in Lat/Lon Format

• Update LoRaWAN Stack

v4.0.9 - 05.10.2018

• Update LoRaWAN Stack

v4.0.7 - 15.08.2018

• Fixed bugs with some LoRaWAN Network providers

v4.0.6 - 28.05.2018

• Clear pending mems IRQ before sleep
• Updated internal state handling

v4.0.4 - 20.03.2018

• Disable mems in active mode

v4.0.3 - 20.03.2018

• compile against new board revision (lower power in sleep)
• disable external rtc
• default tx power to 14dBm

v4.0.2 - 23.02.2018

• Fix lost GPS messages due to broken CRC checks

v4.0.1 - 29.01.2018

• Port to LoRa v3.2 Board

v3.2

• Measure vBat when 3.3V Step Up is off
• Add config parameter gps timeout
• Add config parameter LoRaWAN ADR

v3.1

• Enable buttons for sending (Reed contact connectors)