Firmware Downloads
| Note | ||
|---|---|---|
| ||
The device will not work if an incompatible firmware is installed. If you are unsure, which hardware revision your device is, check with the description of hardware revisions. |
Current Hardware Revision 3
| app-lorapp-lorawan-gps-8.0.6.hex (hardware v3.x) [current release] |
Legacy Hardware Revision 2
| Note |
|---|
This hardware revision is no longer available for sale! Consider using the improved HW Rev 3. |
Downloads:
app-lorawan-gps-button-6.1.0.hex (hardware v2.x) [current release] |
Legacy Hardware Revision 1
| Note |
|---|
This hardware revision is no longer available for sale! Consider using the improved HW Rev 3. |
Downloads:
| Info |
|---|
The LoRaWAN GPS data uplink data encoding has been changed between firmware 4.x ("legacy format") and 5.x. See the manual for details. |
app-lorawan-gps-button-5.0.5.hex (hardware v1.x) |
app-lorawan-gps-button-4.0.9.hex (hardware v1.x) |
Changelog
| Markdown |
|---|
# Changelog `app-lorawan-gps` – GPS-Tracker, Firmware for new dedicated GPS-Board (v3). This replaces the firmware `app-lorawan-gps-button`. ## 8.0.6 - 2021-02-11 ### Fix - Temperature sensor caused an reset on latest hardware batch ## 8.0.5 - |
2020-08-10 |
Fix
### Fix - LoRaWAN: NewChannelReq can remove channels by setting the Frequency to 0 instead of just disable them |
- LoRaWAN: Fix bug where NBTrans > 1 leads to multiple responses from LoRaWAN stack |
## 8.0.4 - 2020-08-06 |
Fix
- Fix internal Selftesting result format.
### Fix - Fix internal Selftesting result format. ## 8.0.3 - 2020-08-06 |
Fix
- Remove random payload in reboot request ACK upload
### Fix - Remove random payload in reboot request ACK upload ## 8.0.1 - 2020-08-05 |
Fix
- Fix config problem with low SF.
### Fix - Fix config problem with low SF. ## 8.0.0 - 2020-08-05 |
Changed
Change official product name to LOB### Changed - Change official product name to `LOB-S-GPS-LW- |
3`. |
- Verify LoRaWAN Stack using official testing tool by LoRaWAN-Alliance. |
- Remove OpMode (class C), ADR, and time sync over LoRaWAN |
- Change internal logic of LostReboot-feature to use ACKs for checking for Network. |
Added
- Low Voltage Protection
Fix
- Fix Voltage StepUp logic for GPS and LoRa
- Send uplink before reboot when ACK required.
v7.1.0 - 17.06.2020
Added
- Add timestamp for last movement event to Port 2 payload
- Add config parameter
movementDistancethat configures how GPS-position changes are calculated as movement events.
Fixed
- LoRaWAN 1.1 issue that sometimes led to invalid DevNonces used for OTAA Join.
- Make sure, mode changes from active to passive are reported in final uplink before change
- Fix an issue that could lead to all zero position data sent as valid position
- Upgrade to Lobaro LoRaWAN Stack 1.2.2 (RX Window adjustment).
v7.0.0 - 28.04.2020
### Added - Low Voltage Protection ### Fix - Fix Voltage StepUp logic for GPS and LoRa - Send uplink before reboot when ACK required. ## 7.1.0 - 2020-06-17 ### Added - Add timestamp for last movement event to Port 2 payload - Add config parameter `movementDistance` that configures how GPS-position changes are calculated as movement events. ### Fixed - LoRaWAN 1.1 issue that sometimes led to invalid DevNonces used for OTAA Join. - Make sure, mode changes from active to passive are reported in final uplink before change - Fix an issue that could lead to all zero position data sent as valid position ## 7.0.1 - 2020-06-04 ### Fixed - Upgrade to Lobaro LoRaWAN Stack 1.2.1 (RX Window adjustment). ## 7.0.0 - 2020-04-28 ### Changed - Completely rewrite firmware for new dedicated board with new LoRaWAN features and concepts. - Completely change Payload format. - Listen to MEMS events while not asleep. - Check for movement by GPS to update activity mode. - New LED blinking patterns. ### Added - Start this changelog. - Regular status messages independent of data messages. - New Lobaro LoRaWAN Stack (v1.1, remote Configuration via Downlink, Class C, etc.). - Time sync from GPS. - Change naming from "Alive Mode" to "Passive Mode" for easier distinguishing from "Active Mode". - Reduce power consumption during deep sleep by ~20%. - Removed Cayenne Payload Format |
v6.1.0 - 09.12.2019
- added new parameters to increase accuracy: maxHDOP & maxDataAfterFix
v6.0.3 - 02.08.2019
- fixed temperature sensor readout
v6.0.2 - 22.07.2019
- inverted powerpin for telit module (hardware v2.1)
- added nmea prefix GN ( Glonass+GPS ) to the parser
v5.0.5 - 09.01.2019
- Update LoRaWAN Stack
- Enable stepUp if needed by battery condition
v5.0.4 - 15.11.2018
- update board driver
v5.0.3 - 15.11.2018
- fix signed issue with longitude
v5.0.0 - 26.10.2018
- Add option for Cayenne LLP Payload format
- Adjust payload format to support neagtive values
- Add Altitude
Send GPS coordinates in Lat/Lon Format
Update LoRaWAN Stack
v4.0.9 - 05.10.2018
- Update LoRaWAN Stack
v4.0.7 - 15.08.2018
- Fixed bugs with some LoRaWAN Network providers
v4.0.6 - 28.05.2018
- Clear pending mems IRQ before sleep
- Updated internal state handling
v4.0.4 - 20.03.2018
- Disable mems in active mode
v4.0.3 - 20.03.2018
- compile against new board revision (lower power in sleep)
- disable external rtc
- default tx power to 14dBm
v4.0.2 - 23.02.2018
- Fix lost GPS messages due to broken CRC checks
v4.0.1 - 29.01.2018
- Port to LoRa v3.2 Board
v3.2
- Measure vBat when 3.3V Step Up is off
- Add config parameter gps timeout
- Add config parameter LoRaWAN ADR
v3.1
- Enable buttons for sending (Reed contact connectors)
| Table of Contents |
|---|